Provided by a fully controlled SCR bridge and a reduced quantity of components.

Thanks to a selection of industrialized options and an easy parameter settings for quick onsite adjustments.

Of the product design to improve MTBF and to reduce MTTR.

To optimize battery life.

< 8In not to oversize mains power supply (3-phase).

With the capability to integrate the battery in the charger cabinet.

To deliver appropriate information level to the user.

Up to IP55 for harsh environmental conditions.

With nickel-cadmium and lead-acid batteries, vented or gas-recombination types.

Between input and output.

Digital control and monitoring.

Wide choice of configurations and options.

1-Ph: FP40R10

3-Ph: FP40R30

1-Ph: 230 VAC ± 10%

3-Ph: 400 VAC ± 10%

1-Ph: < 15 ln

3-Ph: < 8 ln

From 47 to 63 Hz

See ratings table

24/48/110/220V

1 %

Disconnected battery (< 2.5 %)

Disconnected battery (< 0.7 %)

Charger status and alarms on displaying Unit

Output voltage, output current, battery Current

With 4 dry contacts

Up to 100 events

Lead acid or nickel cadmium, vented or recombination

From few minutes to several hours, as required

From 83 % to 94 % (according to model)

From 0 to 40 °C (without system derating)

From -20 °C to +70 °C (battery excluded)

< 95 % non condensing at 20 °C

1000 m (without system derating)

Natural or fan-assisted (according to rating)

IP20

Internal protection

≤ 60 dB

Input - Output 2500 VAC / 1 minute

RAL 7035 or RAL 7032

Varying according to ratings and options (consult us)

24 Vdc: 100A

48 Vdc: 40/60/100A

110-125 Vdc : 25/40/60/100A

220 Vdc: 25A

24 Vdc: 35/65/100/160/220/300/400A

48 Vdc: 35/65/100/160/220/220/300/400A

110-125 Vdc: 35/65/100/160/220/300/400A

220 Vdc: 35/65/100/160/220/300A

Input circuit breaker or molded case circuit breaker (16 kA or 36 kA)

Position contact on AC input circuit breaker

Paralleling diode

Dropping diode

DC earth fault monitor

Customer connection on terminal blocks

Ultra low voltage ripple < 0.1 % (48 V)

Measurements of AC input voltage, current and frequency

Battery protection (fuses or circuit breaker with contact)

Protection against battery reversed polarity

Battery Low Voltage Disconnection (LVD)

Battery Low Voltage Disconnection (LVD) Temperature sensor for battery charge compensation

Test battery presence or test battery capacity

Operating temperature up to 55 °C (with system derating)

External ingress protection IP21, 23, 40, 41, 43, 55

Space heater with hygrostat and/or thermostat

Internal lighting

100 mm or 200 mm base frame

Lifting eyes

DC output protection (fuses or circuit breaker with contact)

Distribution board (circuit breaker with or without contact)

Modbus RS485

Remote alarm up to 8 additional relays

Single rectifier with no battery

Dual charger in single cabinet

Dual charger with shared battery

Batteries in charger cabinet (on shelves or drawers)

Other RAL painting colour

2006/95/EC (before April 2016)

2014/35/EU (after April 2016)

2004/108/EC (before April 2016)

2014/30/EU (after April 2016)

Semiconductor converters - Part 1-1: Specification of basic requirements

Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments

Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standards for industrial environments

Low voltage switchgear and controlgear assemblies - Part1: General rules

Information technology equipment - Safety - Part 1: General requirements

Procedure for type tests for rectifier-battery charger and batteries